BRAZED HARDMETAL TOOLING
Cemented Carbide Brazed Tips and Assemblies
Technical sourcing of standard and drawing-based cemented-carbide tips, steel-supported parts and finished brazed tools.
MNK-G.S.A coordinates the hardmetal tip, support or shank, joint materials, manufacturing route, inspection and delivery as one controlled sourcing package. The carbide grade, tip geometry and brazed joint must be specified together rather than selected as independent catalogue items.
What the Supply Package Can Include
Carbide Tips
Pressed or machined blanks, standard brazing-tip geometries and drawing-based tips supplied as sintered, ground or otherwise finished items according to the agreed drawing.
Brazed Assemblies
Carbide joined to a steel shank, pocket, holder or support, with the base material, filler metal, joint design, thermal route and final machining defined in the manufacturing package.
Finished Tools
External or internal turning tools, special form tools and selected milling-tool configurations supplied to the applicable standard or an approved customer drawing.
Standards and Their Exact Boundaries
| Reference | Public scope summary | Procurement boundary |
|---|---|---|
| ISO 242:2014 | Tip dimensions for brazed turning tools. | Specify the carbide grade, filler and joint acceptance separately. |
| ISO 243:2014 | Types and dimensions of external carbide-tipped turning tools. | Limited to external tools within the stated scope, not all custom assemblies. |
| ISO 514:2014 | Types and dimensions of internal carbide-tipped turning tools. | A non-standard internal tool still requires an agreed drawing. |
| ISO 10145-1:2016 | Dimensions of end mills with brazed helical hardmetal tips and plain or flatted parallel shanks. | Check the shank type and drawing; this is not a universal milling-cutter specification. |
| ISO 10145-2:2016 | Dimensions of the corresponding end mills with 7/24 taper shanks for manual or automatic tool changing. | Confirm the tool-change interface and configuration; custom assemblies need separate definition. |
| ISO 17672:2024 | Brazing-filler composition classes and technical delivery conditions. | Filler classification does not qualify the joint or establish process settings. |
| ISO 18279:2023 | Brazed-joint imperfection classification and guidance on quality levels. | It does not set universal acceptance levels. Define verifiable requirements for the particular joint and service. |
This table and the Finder use the same reference record. These short scope summaries do not replace the standards, drawings or agreed acceptance requirements. Table review date:
A standardised tip shape is not a complete order specification. Grade, condition, tolerances, support geometry, braze filler, process controls and inspection evidence remain separate requirements.
Specify the Hardmetal and the Joint Together
Hardmetal Definition
- Governing grade or customer specification
- Declared WC, binder and permitted additions
- Grain-size and microstructure requirements
- Density, hardness, porosity and other acceptance limits
- Sintered, ground or finished supply condition
Assembly Definition
- Support or shank material and heat treatment
- Pocket, overlap, clearance and joint geometry
- Filler metal, flux or controlled atmosphere
- Heating method and permitted thermal cycle
- Final grinding, marking and inspection route
Brazing cemented carbide to steel involves different thermal expansion and heat-flow behaviour in the two materials. Joint geometry and the controlled manufacturing route therefore form part of the technical requirement. MNK-G.S.A does not infer a brazing procedure from the tip grade alone.
Drawing and Dimensional Control
- Identify whether dimensions apply to the loose tip, the support before joining or the finished assembly.
- Define datums, critical faces, angles, radii, edge preparation and grinding stock.
- State whether the carbide is required as-pressed, as-sintered, ground or finish-machined.
- Show the joint line, pocket, overlap and any required braze-gap controls.
- Separate general tolerances from characteristics requiring individual inspection records.
- Specify final run-out, alignment, tool orientation and marking where relevant.
For reverse engineering, a physical sample is useful only when the customer also defines which features and material characteristics must be reproduced or improved.
Inspection and Traceability
The inspection plan should distinguish the hardmetal batch, the steel or support batch, the brazing consumable and the completed joint. Required evidence may include incoming material certificates, dimensional reports, visual inspection, agreed joint-quality checks, hardness or microstructure results for the carbide, and final identification of the assembled tool.
Use the separate Cemented Carbide Inspection and Test Methods guide to define density, hardness, rupture strength, microstructure, porosity, coercivity and chemistry requirements. Test-method compliance does not itself establish acceptance limits.
Brazed Tip and Assembly RFQ Checklist
- Tip standard, designation or drawing
- Required hardmetal grade and specification
- Loose tip, semi-finished assembly or finished tool
- Support material and heat-treatment condition
- Quantity and production or prototype status
- Brazing filler or approved process requirement
- Critical dimensions and final tolerances
- Application, loads and operating conditions
- Inspection and traceability documents
- Delivery destination and required date
Related Hardmetal and Tooling Resources
- Cemented Carbide Cutting Tool Blanks and Rods — solid blanks, rods and preforms for cutting-tool production.
- Carbide Dies for Cold Heading and Wire Drawing — drawing-based forming-tool procurement.
- ВК / WCo / YG Grade Verification — controlled comparison of hardmetal designation traditions.
- Hardmetal & Tooling — sourcing hub for hardmetal products and technical tooling requirements.
- Machining & Tooling — industry route for machining plants, toolmakers and distributors.
Send Your Brazed Hardmetal Inquiry
Send the drawing or standard designation, required grade, support material, joint requirement, quantity, inspection documents and delivery destination.
Sources and scope checked
Source review date:
Review limits: Only the seven linked public ISO scope descriptions, not full standard text or all page content.
- ISO 242:2014
Tip dimensions for brazed turning tools.
- ISO 243:2014
Types and dimensions of external carbide-tipped turning tools.
- ISO 514:2014
Types and dimensions of internal carbide-tipped turning tools.
- ISO 10145-1:2016
Dimensions of end mills with brazed helical hardmetal tips and plain or flatted parallel shanks.
- ISO 10145-2:2016
Dimensions of the corresponding end mills with 7/24 taper shanks for manual or automatic tool changing.
- ISO 17672:2024
Brazing-filler composition classes and technical delivery conditions.
- ISO 18279:2023
Brazed-joint imperfection classification and guidance on quality levels.
